Stereo & Door Removal

[Dookie]

When I ordered my amp from Crutchfield and they sent me several pages of installation instructions. Here are a few pages that I scanned. Major props for Crutchfield!!:tup:


The front door removal is the same for the rear door. There are 2 clips behind the front door and one for the rear once you pull the panel off. The removal of the speakers is self explanatory, 3 screws around the woofer and a plug. The tweeter up front has 2 screws and a plug.

Attached is the wiring diagram for the radio and climate controls. I've made notes as to which color wire goes to which plug. Important: when installing an amp or sub, make sure you tap (not cut) onto the ACC wire. If you use the ANT wire, your amp or sub will turn off when you switch to the cd. selection.

[Dookie]

Here are some pics of my removal.

First unscrew the shift knob then pop off the plastic surround.
http://im1.shutterfly.com/media/47b7d731b3127ccec240073d39fe00000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Slide the plastic surround out and unplug the lighter.
http://im1.shutterfly.com/media/47b7d731b3127ccec240eff2b87500000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Unscrew the 2 screws at the base.
http://im1.shutterfly.com/media/47b7d730b3127ccec243e792c07100000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Pop off the plastic side molding
http://im1.shutterfly.com/media/47b7d731b3127ccec24174d459fa00000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

[Dookie]

Remove the 3 screws on both sides of the radio. Total of 6 screws.
http://im1.shutterfly.com/media/47b7d731b3127ccec240be78f84f00000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Slide the radio out
http://im1.shutterfly.com/media/47b7d731b3127ccec2419e09595200000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

Closeup of the radio's wiring
http://im1.shutterfly.com/media/47b7d731b3127ccec240409079e800000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/

[Dookie]

Here are some pics of the line-out converters to RCA's


Line-out converters (1 for the fronts, 1 for the rears)
http://im1.shutterfly.com/media/47b7d731b3127ccec2417c6fd87500000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/


RCA's connect. (4 lines = 4 ch)
http://im1.shutterfly.com/media/47b7d731b3127ccec24034ea79a800000010O00AZtHDZo1bt2 IPbz4S/cC/f%3D0/ps%3D50/r%3D0/rx%3D550/ry%3D400/


Enjoy!!

[SubieChik]

Is that a blister on your thumb from all of that hard work?? :D

[Dookie]

Yes it is, thank you for noticing. I got it from digging in my backyard before I started this project. Hurts like a SOB.

[SubieChik]

I bet it does. It is one of those ones that if you pop it water will come out and it will sting like a b!tch huh? Gotta love 'em.

[Dookie]

Edit to my blister. I placed a white dot on it, so you won't stare at it.:lol:

[SubieChik]

:rofl: Ahhh that makes it worse!

[Dookie]

You're killing me smalls!

[Dookie]

Edit pics again, it's getting better.:lol:

[KA82]

meh .

[SleepedGT]

i have an 07 subaru legacy gt with a premium sound system and im not to sure if it has a stock amp somewhere or something. i put in a downline converter for my RCA's and now all the sudden my right speakers wont play or blew. i hooked the downline converter up to the left door speaker.. what should i do??

[Dookie]

If you have a factory Sub it would be located under the driver seat. Recheck your wires again at the converter, make sure you didn't cross the wires. It sounds more like a short than blown speakers, even blown speakers will make some sort of sound. Check all the wiring from the radio to each speakers making sure no open wires are touch any metal surfaces.

I had this problem before in a previous car where one of the speaker wires slipped off the terminal and was touching the metal part of the door.

Hope this helps.

[brownrice]

TY dooks!:tup:

[SleepedGT]

OK thank you, i pligged my RCA's back into the converter and my system is playing fine. i turned down the amp level just to be safe. now when i find the stock amp what do i have to do with that for my highs? cause i want to keep the stock highs..

[Dookie]

The stock amp is inside the factory head unit. If you want to keep the stock tweeters, you could try to splice the wires connecting to your converter. Something like this....

[SleepedGT]

ok now which wires do i splice the converter into. cause i plugged it back into the rear highs and it works now.. idk how long it will last for?

[Dookie]

First of all, what are you trying to do, and what is your final goal to your stereo install? I'm starting to get a little confussed on your main goal here.:o